3M MALAYSIA SDN BHD ======================================================================== CHEMICAL SAFETY DATA SHEET ======================================================================== Document id : 21-3991-3 Issue date : 21/02/2008 Version : 2.00 Supersedes date : 17/11/2006 Document status : Issued This CSDS has been prepared by Toxicology Department 3M Malaysia Sdn. Bhd. ------------------------------------------------------------------------ SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION ------------------------------------------------------------------------ Tradename 3M(TM) Scotch-Brite(TM) Wheels, Light Deburring Wheels, 6S, 7S, 8S; Deburring Wheels (EXL/EX2/EX3), 9S FIN, 8S FIN 3M Product ID: 61-0000-1965-5, 61-0000-1994-5, 61-0000-2221-2, 61-0000-2259-2, 61-0000-2928-2, 61-0000-2930-8, 61-0000-2931-6, 61-0000-4617-9, 61-0000-4618-7, 61-0000-4619-5, 61-5000-8942-2, 61-5000-9973-6, 61-5000-9977-7, 61-5000-9979-3, 61-5001-0409-8, 61-5001-2485-6, 61-5001-2487-2, 61-5001-2489-8, 61-5001-2491-4, 61-5001-2492-2, 61-5001-2560-6, 61-5001-2704-0, 61-5001-2705-7, 61-5001-2706-5, 61-5001-2708-1, 61-5001-2707-3, 61-5001-2709-9, 61-5001-2710-7, 61-5001-3311-3, 61-5001-3312-1, 61-5001-3315-4, 61-5001-3316-2, 61-5001-3322-0, 61-5001-3499-6, 61-5001-3700-7, 61-5001-3657-9, 61-5001-4617-2, 61-5001-4619-8, 61-5001-4622-2, 61-5001-4623-0, 61-5001-4624-8, 61-5001-4625-5, 61-5001-4754-3, 61-5001-4981-2, 61-5001-4755-0, 61-5001-5943-1, 61-5001-5952-2, 61-5001-5958-9, 61-5001-5962-1, 61-5001-5965-4, 61-5001-5984-5, 61-5001-5986-0, 61-5001-5987-8, 61-5001-5988-6, 61-5001-5989-4, 61-5001-5991-0, 61-5001-6344-1, 61-5001-7712-8, 61-5001-7713-6, 61-5001-7714-4, 61-5001-7715-1, 61-5001-8053-6, 61-5001-8146-8, 61-5001-8179-9, 61-5001-8278-9, 61-5001-8445-4, 61-5001-9157-4, 61-5002-9023-6, 61-5002-9024-4, 61-5002-9128-3, 61-5002-9195-2, 61-5002-9223-2, 61-5002-9224-0, 61-5002-9225-7, 61-5002-9226-5, 61-5002-9227-3, 61-5002-9228-1, 61-5002-9229-9, 61-5002-9230-7, 61-5002-9231-5 Intended Use of Product Abrasive Product COMPANY IDENTIFICATION ---------------------- Manufacturer's name and address 3M 3M Center St. Paul, Minnesota 55144-1000 USA Importer's name and address 3M Malaysia Sdn. Bhd. Bangunan 3M No. 6, Persiaran Tropicana 47410 Petaling Jaya Selangor Telephone number 03-7806-2888 Emergency telephone number 1-651-7376501 ( 24 hours ) CONTACT POINT ------------- Designation Toxicology Coordinator Telephone number 03-7806-2888 ------------------------------------------------------------------------ SECTION 2: COMPOSITION/INFORMATION ON INGREDIENT ------------------------------------------------------------------------ Ingredient name CAS number Percentage ------------------------------------- ------------------ ------------- SILICON CARBIDE MINERAL 409-21-2 20 - 60 CURED ADHESIVE Unknown 30 - 50 NYLON WEB BACKING 32131-17-2 1 - 15 FILLER 14807-96-6 1 - 5 LUBRICANT 4485-12-5 < 3 ------------------------------------------------------------------------ SECTION 3: PHYSICAL AND CHEMICAL PROPERTIES ------------------------------------------------------------------------ Physical form,Color,Odor Solid Abrasive Product Water Solubility N/A % Boiling point/boiling range N/A C Melting point/melting range N/A C Vapour pressure N/A mmHg Percent Volatile No data available. Evaporation rate No data available. Vapour density N/A Specific gravity N/A Flash point N/A C Autoflammability N/A C Flammable Limits - LEL N/A % Flammable Limits - UEL N/A % Viscosity No data available. ------------------------------------------------------------------------ SECTION 4: HAZARD IDENTIFICATION ------------------------------------------------------------------------ Risk Phrases None ------------------------------------------------------------------------ SECTION 5: FIRST AID MEASURES ------------------------------------------------------------------------ Instructions for Ingestion No need for first aid is anticipated. Instructions for Eye Contact Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Instructions for Skin Contact Wash affected area with soap and water. If signs/symptoms develop, get medical attention. Instructions for Inhalation Remove person to fresh air. If signs/symptoms develop, get medical attention. ------------------------------------------------------------------------ SECTION 6: FIRE FIGHTING MEASURES ------------------------------------------------------------------------ Suitable Extinguishing Media Ordinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam). Fire Fighting Procedures Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Special Instructions for Fire Fighting Not applicable. ------------------------------------------------------------------------ SECTION 7: ACCIDENTAL RELEASE MEASURE ------------------------------------------------------------------------ Spill Response Not applicable. Methods for Disposal Not applicable. ------------------------------------------------------------------------ SECTION 8: HANDLING AND STORAGE ------------------------------------------------------------------------ Storage Requirements Store in a cool, dry place. Ventilation Avoid breathing of dust created by sanding, grinding or machining. Use Instructions Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Sparks and particles flying from the product during sanding or grinding can cause injury and fire. ------------------------------------------------------------------------ SECTION 9: EXP0SURE CONTROL AND PERSONAL PROTECTION ------------------------------------------------------------------------ SILICON CARBIDE MINERAL (409-21-2) Exposure Limits 10 mg/m3 3 mg/m3 0.1 FIBER/CC ACGIH: TWA - inhalable fraction; non-fibrous. ACGIH: TWA - respirable; non-fibrous. ACGIH: TWA - specific form; as fibers >= 5 um; Table A2; Fibrous forms , including whiskers. NYLON WEB BACKING (32131-17-2) Exposure Limits 5 mg/m3 CMRG: TWA; as respirable dust; Comments: Per MSDS dated 3/21/06 for 11-0025-1430-2. 10 mg/m3 CMRG: TWA; as total dust; Comments: Per MSDS dated 3/21/06 for 11-0025-1430-2. FILLER (14807-96-6) Exposure Limits 2 mg/m3 0.5 mg/m3 ACGIH: TWA - respirable; Table A4; CMRG: TWA - specific form; as respirable dust; DUPONT MSDS DATED 10/28 /99 FOR 11-0004-3257-2. LUBRICANT (4485-12-5) Exposure Limits 10 mg/m3 ACGIH: TWA - as total dust; Table A4; Particulates not otherwise class ified. - Category: STEARATES. Recommended Ventilation Use with appropriate local exhaust ventilation. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or airborne particles. If ventilation is not adequate, use respiratory protection equipment. Eye Protection Avoid eye contact. To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or grinding operations or when near such operations. Hand Protection Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Wear appropriate gloves to minimize risk of injury to skin from contact with dust or physical abrasion from grinding or sanding. Skin Protection Avoid skin contact. Respiratory Protection Provide appropriate local exhaust ventilation for sanding, grinding or machining. Avoid breathing of dust created by sanding, grinding or machining. Assess exposure concentrations of all materials involved in the work process. Consider material being abraded when determining the appropriate resipratory protection. Select and use appropriate respirators to prevent inhalation overexposure. Ingestion Wash hands after handling and before eating. Not an expected route of exposure. ------------------------------------------------------------------------ SECTION 10: STABILITY AND REACTIVITY ------------------------------------------------------------------------ Hazardous Decomposition Carbon monoxide During Combustion Carbon dioxide During Combustion Oxides of Nitrogen During Combustion Stability and Reactivity Hazardous polymerization will not occur. Stable ------------------------------------------------------------------------ SECTION 11: TOXICOLOGICAL INFORMATION ------------------------------------------------------------------------ Effects from Eye Contact Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion. Dust created by cutting, grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Effects from Skin Contact Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching. Effects from Inhalation Dust from cutting, grinding, sanding or machining may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Prolonged or repeated exposure may cause: Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and changes in lung function tests. Effects from Ingestion No health effects are expected. Other Toxicological Information This document covers only the 3M product. For complete assessment, when determining the degree of hazard, the material being abraded must also be considered. ------------------------------------------------------------------------ SECTION 12: ECOLOGICAL INFORMATION ------------------------------------------------------------------------ Environmental Data No data available. Ecotoxicity Data Not determined. Ecofate Data Not determined. ------------------------------------------------------------------------ SECTION 13: DISPOSAL INFORMATION ------------------------------------------------------------------------ Product as Sold Dispose of waste product in a sanitary landfill. As a disposal alternative, incinerate in an industrial or commercial facility. Product after Use The substrate that was abraded must be considered as a factor in the disposal method for this product. ------------------------------------------------------------------------ SECTION 14: TRANSPORT INFORMATION ------------------------------------------------------------------------ UN Number IMO Class ICAO Class Special Instructions ** NOT HAZARDOUS FOR TRANSPORT FOR DOT, IMO OR IATA. ------------------------------------------------------------------------ SECTION 15: REGULATORY INFORMATION ------------------------------------------------------------------------ Symbols None Risk Phrases None Safety Phrases None Special Regulatory Information Contact 3M for more information. ------------------------------------------------------------------------ SECTION 16: OTHER INFORMATION ------------------------------------------------------------------------ The information on this data sheet represents our current data and best opinion as to the proper use in handling of this product under normal conditions. Any use of the product which is not in conformance with this data sheet or which involves using the product in combination with any other product or any other process is the responsibility of the user.